InteliSENS® SLmini-i4 W
InteliSENS® SLmini-i4 W
Speed & Length Measurement
The InteliSENS® SLmini-i4 W Series non-contact speed and length measurement gauge has a wide angle lens making it ideal for the measurement of curved surface products in “roll to roll” or “cut to length” processes. Wire, Cable, Hose, Tube, Pipe are good examples. Applications where speed measurement is critical for drive control or where length measurement is critical for product quality will benefit from the increased accuracy of Laser Doppler Speed and Length Measurement.
Focused on connectivity the SLmini-i4 W Smart Sensor with 32bit communications comes preloaded with Profibus, Profinet and Ethernet Industrial Protocol for your PLC connection. Modbus, OPC-UA, RS232, RS485 and WiFi round out a wide range of digital communications for your Industry 4.0 Solution.
- No Moving Parts, Increased Reliability and MTBF
- No Slip, No Wear, No Marking of your product
- Incredibly small and easy to install
- Pulse outputs like your encoder
- Stand Alone Measuring Device or Fully Integrated to PLC
- Industry 4.0 Data Communications
|SLmini 1220-i4 W||SLmini 3060-i4 W|
|Stand Off Distance||120mm
|Depth of Field||20mm
|Minimum Speed||0.1 m/min
|Maximum Speed||2000 m/min
Factory Calibrated to better than 0.05%.
Repeatability of 0.02%
Maximum Acceleration Rate of 500m/s2 (1640ft/s2)
Measurement Rate Up to 24,400/sec
Speed Measurement selectable m/min, ft/min, yd/min
Length Measurement selectable m, ft, inch, yd
Normal (Continuous Length), Batch Length
Automatic Detection and Object Present
Default Output 5vdc or User Input to 24vdc
Max Maximum Frequency 1MHz Pulse Rate Selectable - Pulse/Meter or
Meter/Pulse Configurable as 6 x Single End or 3 Quadrature or 3 Differential.
Non Isolated from Gauge Head, Opto Isolated from the PSU-BOB i4
Maximum Input Voltage 24Vdc
2 x Fixed logic Inputs - Laser Enable and Shutter Enable
3 x Selectable logic Inputs - Reverse Direction, Length Reset, Display Hold, Speed Hold, Total Length Reset, End of Reel
Maximum Voltage 30Vdc, Current 100mA.
N-Channel MOSFET pull-down (for connection to user supplied onto isolated relay)
1 x Fixed Logic Output - Shutter Status
3 x Selectable logic outputs - Gauge Ok, Measuring Speed, Preset Length 1, Preset
Length 2, Good Readings Low, Object Detected, Gauge Hot.
RS232 MODBUS RTU, PROTON ASCII code or Label Printer
USB using RS232 - USB Converter Cable
RS485 MODBUS RTU, PROTON ASCII code (Not available with PROFIBUS)
Connects to Proton Products CDi4 Display
Ethernet selectable between OPC-UA and Modbus
Connect to a PLC using PROFIBUS, PROFINET, or EtherNet I/P, data update rate up to 500/sec. Flexible Data Configuration, Big Endian, Little Endian
Class 3B Visible Laser.
Wavelength 650 - 670 nm, typically 658 nm with a beam diameter of 3mm (0.12”)
Total emitted power 40mW. Power Density at Stand Off Distance 50mW/cm2
Electrical and Operating Requirements
15 - 30 Vdc
*See Accessories for High Temperature Options
Size and Weight
|More than 200 Data Words are available to communicate with your Industry 4.0 Solution. Data Words are divided into distinct function groups to make it easy to select the ones you want.|
|Gauge ID Data Words||Model Number, Serial Number, Firmware APP version, Firmware Core Version, Firmware Date|
|Calibration Data||Last Calibration Date, Days Since Last Calibration, Total Run Time, Calibration Alarm|
|Validation Data Words||SNR, Signal Amplitude, Good Readings, FFT Amplitude|
|Wired Network Info||IP Address, Netmask, Gateway|
|WiFi Network Info||IP Address, Netmask, Gateway, SSID|
|Measurement Data||Instant Speed, Average Speed, Batch Length, Total Length|
|Diagnostic Data||Laser Temperature, APD Temperature, Laser ON/OFF Cycles, Laser Power|